|
Magnetic
Resonance -
Technology
Information
Portal |
Welcome to MRI Technology • |
|
|
 | Info
Sheets |
| | | | | | | | | | | | | | | | | | | | | | | | |
 | Out-
side |
| | | | |
|
| | | | | |
| Result: Searchterm 'Sequences'
found in 59 messages |
| Result Pages: 1 2 [3] 4 5 6 7 8 9 10 11 12 |
More Results:  Database (188) News Service (6) Resources (8) |
|
|
Matt H
Fri. 27 Oct.17,
13:23
[Start of:
'When to shim?'
1 Reply]
 Category:
General
|
| When to shim? |
On what sequences should a shim volume be added? (GE scanner)
|
|  View the whole thread | Reply to this thread
(login or register first) | |
Desiree Dupuy
Sat. 3 Dec.16,
22:14
[Reply (2 of 3) to:
'Muscle shading in 3T Images'
started by: 'Travis Conley'
on Thu. 21 Oct.10]
Category:
Applications and Examinations
|
| Muscle shading in 3T Images |
Try running a B1 Map followed by Calibration. Set RF Drive mode to Optimized. This is supposed to optimize for your Patient. Supposed to reduce dielectric effect/shading for Lumbar and Abdomen.
You can find under GE Additional Abdomen Sequences.
Or you can run Ideal with Dixon technique. Turn on IN phase will give you T1 FS & IN Phase is you plane T1. I believe this takes care of the artifact.
|
| | View the whole thread | | |
Marta Lancione
Thu. 5 May.16,
14:55
[Start of:
'Drawing MRI sequence'
0 Reply]
Category:
General
|
| Drawing MRI sequence |
Does anyone know of existing LaTeX macros or packages or any other software for drawing Magnetic Resonance Imaging pulse sequences?
I didn't find anything online. Thank you so much for your help!
|
| | Reply to this thread
(login or register first) | |
Renate S.
Thu. 5 May.16,
14:27
[Reply (1 of 2) to:
'Contrast on an 3T'
started by: 'Roos van Wieringen'
on Mon. 2 May.16]
Category:
General
|
| Contrast on an 3T |
Studies (for example http://pubs.rsna.org/doi/full/10.1148/radiol.2373041672 , http://pubs.rsna.org/doi/full/10.1148/rg.287075154 ) suggest that contrast enhancement of gadolinium is increased at higher field strengths. That can be used to lower the dose or receive higher contrast effects. It also depends on the contrast sensitivity of the used sequences and the examined body part.
|
| | View the whole thread | | |
Renate S.
Sat. 6 Jun.15,
13:18
[Reply (1 of 2) to:
'is this kind of zebra artifact?'
started by: 'luna xu'
on Fri. 5 Jun.15]
Category:
Artifacts
|
| is this kind of zebra artifact? |
Looks more like a Zipper artifact. Can be caused by electronic noise. Switch off all light bulbs, remove all electronic equipment from the scanner room, make sure that the door is really closed (clean the contacts between door and jam if necessary) and try again. If the artifact consists control the penetration panel where the cables enter the room and the faraday cage, it is possible that there is a leak in the RF shield. If the artifact remains with all coils and sequences you need the service to repair the problem.
|
| | View the whole thread | |
| |
| | Result Pages : 1 2 [3] 4 5 6 7 8 9 10 11 12 | |
|
| |
 | Look
Ups |
| |
|
MR-TIP.com uses cookies! By browsing MR-TIP.com, you agree to our use of cookies. | | | [last update: 2024-02-26 03:41:00] |
|
|
bottom
top
